How To Build On A Steep Incline Using Railroad Tie Stairs

How To Build On A Steep Incline Using Railroad Ties Stairs

Emma DowneyByEmma Downey
Updated on 10/4/2022

Table Of Contents

You may turn a steep slope in your yard into an attractive and safe garden staircase by using railroad tie stairs, which are long-lasting and resistant to decay. This will allow you to make the most of the space you have available. Utilizing railroad ties is one way to accomplish this goal. It is usual to practice applying creosote on the top of railroad ties in order to preserve the beauty of the wood and prevent it from decaying. This serves two purposes. Because the chemicals have the potential to seep into the soil, you should avoid putting railroad tie steps in close proximity to an edible garden. Instead, you should choose another location. You should construct the stairs at a spot that is further away from the garden rather than in the park itself. You also have the choice to use landscaping timbers ideas, which typically have a diameter of between 5 and 6 inches and are fashioned from a type of wood that is inherently resistant to rot, such as the heartwood of cedar or redwood. If you decide to proceed in this manner, it is imperative that the landscaping timbers be treated with an anti-fungal chemical. A set of stairs has been built into the side of the hill in such a manner that they lead all the way up to the top of the terrain, starting from where the landscape meets the ground.

railroad

  1. In the first phase, you will need to adjust the lengths and widths of three railroad ties so that they are suitable for the next step. The width of one of the railroad ties should be equal to the width that is planned for the stairs, and the length of the other two railroad ties should be twice as long as the depth that is scheduled for each stair tread. Additionally, the width of one of the railroad ties should be equal to the width that is planned for the stairs. To ensure that there is sufficient area for feet to step and that climbing the stairs may be done in a manner that is risk-free, the depth of the treads should be anywhere between one and two feet. In order to construct the final steps of the staircase, you will require an extra three railroad ties. Every single one of these railroad ties has to be trimmed down to the exact same dimensions as the first three railroad ties that were used.

railroad

  • It is suggested that the base of the slope is excavated to a depth of around 5 inches and that the space be made as broad as is necessary to accommodate the width of the steps. A cut that is suitably deep will need to be made all the way through the hillside in order to adjust the whole length of both of the side railroad ties. This cut will be necessary in order to accommodate the total size of the railroad ties.
  • It is necessary to fill the gap that was excavated with crushed rock to a depth of four inches, using a hand tamper to ensure that the stone is packed securely into the space. On top of the rock base, spread out an even layer of sand that is one inch thick to provide a foundation for the initial portion of the project that is both stable and has adequate drainage.

  • Put the three railroad ties in a position where they are leaning on the foundation layer of sand and resting there. First, drive wood screws with a length of 12 inches through the sidewalls of the two railroad ties that are situated on the side of the "U." Next, assemble the three railroad ties into the shape of a "U" by connecting them with each other using the side of the "U." After that, insert these wood screws into the newest railroad tie you just installed, which is the third one.

railroad

  • Starting from the center of the side railroad ties on the ground below, dig out the hillside to a depth that is adequate for accommodating the length of the side railroad ties. This depth should be suitable for adjusting the size of the side railroad ties. It is necessary to carry out these steps in order to make room for the length of the side railroad ties. If the treads are to be 24 inches deep and the railroad ties are to be 48 inches long, then you will need to dig into the hillside for a total of 48 inches, beginning at the place in the first course of railroad ties that is centered. This will be required if you want the treads to be the same length as the railroad ties. You will be able to create footprints and railroad ties that are tailored to your requirements as a result of this.
  • Install an extra three railroad ties in the shape of a U on top of the first course of railroad ties that you have already installed. With this, the student will have finished the second course. The railroad ties that are positioned along the edge of the track are required to extend beyond the back of the first course of connections by a distance that is equal to one-half of the length of the ties. This is done so that the relationship can support the weight of the track. You will need to drive landscape timber screws that are 12 inches long in order to connect the second course of railroad ties to the first course, and this will be landscape timber projects, as well as attach the side timbers to the railroad tie that is positioned at the front of the U-shape. In addition, you will need to carry out these steps in order to link the first and second courses of railroad ties together.

railroad

  • As soon as you reach the crest of the hill, you will need to continue digging the slope in order to make room for the remaining courses of railroad ties. This will be necessary in order to complete the construction of the railroad. On top of the first set of railroad ties, arrange three more relations in the shape of a U. Pay attention to the fact that each new step should overhang the one that came before it by a distance that is equal to half of the length of the previous step. In order for the railroad ties to be linked together, landscape wood screws should be hammered into each individual tie.
  • When it comes to filling up the empty areas that are left between the stair steps, you have the choice of either utilizing concrete or gravel as the material. You also have the option of populating the area with more pieces of railroad tie stairs that move in the other direction, either from left to right or front to rear. Both of these options are available to you. You have the ability to choose any of these two paths.